FAQ
Yes! Naturally occurring hydrocarbon gasses are used as well as specially engineered non-chlorinated gasses that have no impact on stratospheric ozone.
Yes
The Jetclean machine cannot be used for any other than cleaning spray guns with disposable cups.
No, one of the benefits to Jetclean is that no additional air extraction piping is needed. Clean air evacuates outside the unit while the waste is collected in the supplied reservoir.
1 aerosol can be used for approximatively 35 paint gun cleans.
Replacement pre-filters and main filter are available in stock. Please contact your After Sales representative for pricing.
Paint manufacturers recommend to not mix water-based and solvent-based waste in the same collector jug due to the risks of hydrogen gases explosion. To avoid this risk, you can use a 2nd waste collector or install a 2nd Jetclean machine to have 1 machine dedicated to waterborne and 1 machine dedicated to solvent. Please contact you sales representative for information and pricing.
Yes, replacement water and air guns are both available as spare parts. Contact our After Sales representative for the latest pricing.
A pre-charged aerosol is an aerosol spray can pre-fill with propellant and solvent blend. The final aerosol product is achieved by filling the pre-charged can with paint products or other liquid products.
The drawer is a safety precaution for an overfilled waste collector. It holds the same amount of waste as the waste collector supplied.
Dimethyl ether, n-butane, propane, nitrogen, nitrous oxide and carbon dioxide or mixture of the mentioned gasses.
Depend on the requirement and the type of paint used. There are choices of universal solvent blend for general purpose usage and custom blend formulation optimum spray result and finishing.
Yes! Naturally occurring hydrocarbon gasses are used as well as specially engineered non-chlorinated gasses that have no impact on stratospheric ozone.
Yes
Yes, after mixing with hardener/activator. Pot life inside the aerosol can last from 24 to 48 hours depend on the atmosphere temperature. If keep in the refrigerator it can be extend up to 1 week. Or, special 2K aerosols are available from our suppliers that permit hardener to be mixed just before painting.
Yes, with universal pre-charged aerosols or acrylic lacquer pre-charged aerosols.
Yes, with universal pre-charged aerosol or synthetic enamel pre-charged aerosols.
Yes, after mixing with hardener/activator. Pot life inside the aerosol can last from 24 to 48 hours depend on the atmosphere temperature. If kept in a refrigerator, it can be extend up to 1 week. Or, special 2K aerosols are available from our suppliers that permit hardener to be mixed just before painting.
Yes, with universal pre-charged aerosols or acrylic lacquer pre-charged aerosols.
Yes, with non-paint pre-charged aerosols.
Yes, after mixing with hardener/activator. Pot life inside the aerosol can last from 24 to 48 hours depend on the atmosphere temperature. If keep in the refrigerator it can be extend up to 1 week. Or, special 2K aerosols are available from our suppliers that permit hardener to be mixed just before painting.
Yes, after mixing with hardener/activator. Pot life inside the aerosol can last from 24 to 48 hours depend on the atmosphere temperature. If kept in the refrigerator, it can be extend up to 1 week.
Yes, with water-based pre-charged aerosols.
No, The thinners are already contained in the aerosol. Not all thinners are compatible with aerosol use. Therefore the proper thinners for aerosol use are already contained within the aerosol.
It is best and recommended to mix the paint before filling into the filling cap as non mixed pigments can stick onto the sides of the cap (this may change the final colour results).
No, just fill the paint as it is without thinner or reducer.
No. You don’t need to lubricate the machine. There is no need for a lubricator on the air line either.
There are two holes for you to screw the machine on a table or work surface. The Fill-One can be used with a portable support plate or wall bracket to free counter space.
All parts are available. Some as sub assemblies. See After sales service.
We do not provide air filters but we do recommend that one be used as the machine must be used with clean dry air in order to protect from internal rusting.
No need actually. But user needs to keep the machine clean inside, try not to allow paints stick to the pneumatic/air piston.
From 24 to 48 hours depend on the temperature. If keep in the refrigerator it can be extend up to 1 week.
The whole filling process takes 5 to 20 seconds depend on paint viscosity (excluding paint preparation and mixing).
It depends on how many colours and how many types of paints. On average an experience user can fill up to 500 cans per day.
The Fill-One is design to fill 400ml cans with 100ml of paint. The rest of the volume is the solvents and gas propellant.
Standard filling is 100ml – the aluminium cup is marked with a line at the 100ml volume.
You can use the proper thinner adapted to the paint used to clean any paint stain on the internal parts of the machine. Just follow the pictures inside the user’s manual.
Just follow the pictorial guide in Installation & Operating Manual.
Just follow the pictorial guide in Installation & Operating Manual for usage and filling process. It is very simple.
There are virtually no “Wear and tear” parts as the disk on the caps is the piston head that is changed with each use.
2 years.
Besides pearl/mica or special effect pigment. Impurities such as dried paint, dust or sand. Or sometimes paint that did not stir well before filling may cause blockage too.
A pre-charged aerosol is an aerosol spray can pre-fill with propellant and solvent blend. The final aerosol product is achieved by filling the pre-charged can with paint products or other liquid products.
0.5 liter per stroke.
Minimum 1 hp. Any compressor whether big or small that can generate 1 hp or more (horse power actually relates to air volume rather than working pressure). Actual requirement is working pressure of: minimum 7 bar/100psi. Maximum 9 bar/130psi.
Normally special effect colours where the pigment particles may be too large for the aerosol spray valve system. Especially pearl and mica pigments.
Dimethyl ether, n-butane, propane, nitrogen, nitrous oxide and carbon dioxide or mixture of the mentioned gasses.
Depend on the requirement and the type of paint used. There are choices of universal solvent blend for general purpose usage and custom blend formulation optimum spray result and finishing.
The fact that each aerosol is delivered with one unique filling cap prevents this possibility. However, if one was to purposely use two filling caps to overfill the aerosol, the aerosol can would not explode but there may be leakage from the valve and the aerosol would deform (aerosol safety concept).
Simply because there are many types of paints. The various pre-charged aerosols are designed to get optimum finish results.